S-wave filling 
 First, the performance advantages: the design of novel packing structure, the hydrophilic area, the cooling effect, flame-retardant performance. Second, the specification: Dimensions: 1000 × 500mm 
 From the film: 35mm 
 Thickness :0.35-0 .5 mm 
 Third, to adapt to temperature: 65 ℃ ~ -35 ℃ 
 Fourth, the scope: a square cooling tower, hyperbolic cooling towers. 

 Oblique cross filler 
 I. Features: This packing has advanced technology, reasonable design, data reliability, durability, test and production run that through the cooling effect, air resistance is small, hydrophilic performance, contact area, film, and easy to fill thermal conductivity, chemical stability, acid, alkali and organic solvents, corrosion, etc.. Angle wrong filler material forms a staggered ring assembly, packing film tilt angle is generally 60o, the current factory production of polyvinyl chloride (PVC), polypropylene (PP) diagonal cross fill two materials. 
 Second, the specification: 50 × 25 × 60 ° 
 Width: 250mm 
 Length: according to user needs 
 Slice thickness: 0.35-0.6 ± 0.05mm 
 Third, the application temperature: 65 ℃ ~ -35 ℃ 
 Fourth, the scope: Round cooling tower 

 Step-ladder ramp fillers 
 I. Features: step-ladder ramp fillers by the Electric Power Research Institute Water Resources Institute of the cooling water design, the filler piece type cross-section was trapezoidal ramp to improve the packing of soft drinks, and slow moving water film under torsion splashing speed, Fill in the extended heat exchange time, to improve thermal performance. Has good overall performance. Channel bonding large area solid, the overall assembly of rigidity, and can be widely used for industrial cooling towers, factory currently produces polyvinyl chloride (PVC), polypropylene (PP) of two materials. Flame-retardant performance, oxygen refers to ≥ 30 
 Second, Width: 250,300,350,400 mm 
 Length: not limited. 
 Thickness :0.35-0 .5 mm 
 Third, the application temperature: 65 ℃ ~ -35 ℃ 
 Fourth, the scope of application: industrial cooling tower 

 Difference-bit sine wave filler 
 I. Features: poor packing by the sine wave sine-position difference is made between the film and the film adhesive fixed to the convex cone, with good rigidity and heat resistance properties. Flame-retardant properties, and oxygen index ≥ 30 
 Second, the specification: 
 Width: 500mm Length: 1000 ~ 1500mm. 
 Thickness :0.35-0 .5 mm 
 Third, the application temperature: 65 ℃ ~ -35 ℃ 
 Fourth, the scope: 

 Point wave filler 
 I. Features: light weight, easy installation, fire-retardant properties, good chemical resistance, cooling, high efficiency, wide application and so on. 
 Second, the specification: 
 Dimensions: 1000 × 500mm 
 From the film: 25mm 
 Slice thickness: 0.25-0.3mm 
 Third, the application temperature: 65 ℃ ~ -35 ℃ 
 Fourth, the scope: a square cross-flow cooling tower 

 Hexagonal honeycomb packing 
 Produced hexagonal honeycomb filler pipe and straight pipe are inclined in two forms. Materials have two kinds of polypropylene and fiberglass. Inclined tube is mainly used for a variety of sediment and sand removing effect. Water supply and drainage project in the last ten years the most widely used and become a water treatment plant. It is suitable for a wide range of treatment effect is high, small footprint advantages. Sand for the intake, general industrial and domestic water sedimentation, sewage sediment, grease, and Owari enrichment process, which applies to new construction, but also for the transformation of the existing old pool, has achieved good economic results. 
 I. Features: 
 1, wet weeks, the hydraulic radius. 
 2, a good state of laminar flow, particle deposition from turbulent flow interference. 
 3, when the oblique tube length of 1 m, the effective load by 3-5 tons / m 2 ? when the design. VO control 2.5-3.0 mm / s range, the best water quality. 
 4, using the inclined tube sedimentation tanks with a capacity when the flow sedimentation tank 3-5 times the speed clarifier clarifiers and pulse 2 times.